If you are using Windows 7, you will need to clone the Windows 10 IoT Enterprise Image from our Discord Server as Windows 7 - Windows 11 will remove all files and apps.
{.is-danger}
When preparing, you will need to grab the Windows 11 IoT Enterprise LTSC ISO from here and download the Windows 11 IoT Enterprise LTSC link. We recommend the 2nd link as its already set to iso. You will need to install the ISO to your Kiosk PC or use a tool like Rufus to extract the ISO to your USB Flash Drive
Open the ISO we downloaded to the Kiosk PC or plug in your USB Flash Drive
In the initial setup, you will be asked about Updates. If your kiosk is offline, you will need to set it to Not right now. If your kiosk is connected to the internet, you can download updates, drivers, and optional features.
When prompted for a product key, you should be able to skip this step.
When asked to select an image, select Windows 11 IoT Enterprise LTSC.
If you successfully did everything correctly, you should be able to select Keep personal files and apps but sometimes this is automatically applied. Once you verified everything, proceed with installation.
Once the kiosk boots into Windows 11, you should activate windows as after 30 days, the kiosk will turn off automatically after 2 hours. You will need an internet connection to complete this. We recommend MAS as obtaining an IoT Enterprise License isn't given out to just anyone.
#Upgrading from 3rd/4th Generation to 5th Generation Cortex Barcode Scanner
This is for upgrading from 3rd/4th Generation to 5th Generation. Typically this is beneficial as 4th Generation tends to have high amounts of issues during kiosk restarts, which tends to relieve long term issues.
Disconnect the USB Cable and Cable J7 on the DVD-36-000-04 Gripper Board
Loosen 2 Bolts Holding the old Camera Device
Grab the Cortex Barcode Scanner and mount to the bracket.
Install the Cortex Barcode Scannner using the same 2 bolts holding the old mount
Install the 5th Generation Camera from the Redbox Technician Driver Kit.
If you are using Windows 11, you will need to use the CR1100 drivers from CodeCorp's Website, which also support CR1000 devices.
{.is-warning}
Modify hal.xml and apply the following to the camera properties:
Open Command Prompt and execute reg.exe add "HKLM\SYSTEM\ControlSet001\Services\CCSERMU\Configuration\000000000000" /v PortName /t REG_SZ /d "COM6" /f
Restart the computer
If done correctly, your Cortex Barcode Scanner Should work as expected. If you are getting a scanning error, Double check the steps above were followed correctly.
For this, we will be using Macrium Reflect 8 (X works the same, but it is trialware and only restoring works after the trial period) though there are other tools to clone to a drive. You will need to prep the PC.
This is for cloning your previous OS from your physical drive.
Disconnect the HardDrive from the Kiosk PC
Plug the Harddrive and Solid-State Drive into your PC (Recommended) or a SATA Drive Dock.
Open Macrium Reflect.
Locate Backup and select Image Selected Disks.
Select the drive you wish to back up and restore on a Solid-State Drive.
You can skip the Edit the Plan for this Backup window as this is not required for our backup
Check advanced options and make sure the Compression Level is set to Medium and use Intellegent sector copy.
If your backup fails upon restoring, you can set Compression Level to None which sometimes solves this issues.
{.is-danger}
Press Finish and your backup should start. We recommend using Macrium Reflect 8 at the Highest Priority to speed up the backup process.
Once Finished, you will need to navigate to Restore and look for Browse for an image or backup to restore... and select the image we just backed up.
Press Restore once you verify the contents match what we backed up earlier.
Make sure you select the correct target disk, then select Erase Disk and Copy Partitions.
Press Finish and Macrium should start restoring.
Unplug the Solid-State Drive from your PC or Dock and Plug it back into your Kiosk PC.
Boot up the PC and verify it boots properly before plugging all the cables back into your kiosk and screwing the Solid-State Drive to the mount in the case.
Wanting to upgrade to the Windows 10 Image or having to get the Windows 7 Image because the drive was dead on arrival or missing? This section should help with restoring. You will need to get the images from the discord server.
Plug the Harddrive (7200 RPM Recommended. 5400 RPM will have a hard time querying the VistaDB database and may crash the kiosk software) or Solid-State Drive (Recommended) into your PC (Recommended) or a SATA Drive Dock.
Open Macrium Reflect.
Navigate to Restore and look for Browse for an image or backup to restore... and select the image we downloaded from the discord server.
Press Restore.
Make sure you select the correct target disk, then select Erase Disk and Copy Partitions.
Press Finish and Macrium should start restoring.
Unplug the drive from your PC or Dock and Plug it back into your Kiosk PC.
Boot up the PC and verify it boots properly before plugging all the cables back into your kiosk and screwing the Solid-State Drive to the mount in the case.
If you start experiencing issues, you may need to repeat all steps again after re-downloading the image. Also follow Migrate from old kiosk to new kiosk guide to get your kiosk running with settings from your old kiosk.
{.is-warning}
Electrical work must be performed with extreme caution and precision. If you are unsure about any part of this process, or lack the proper tools or experience, stop immediately and consult a licensed electrician. Improper wiring can result in serious injury, death, fire, and/or damage to kiosk equipment.
{.is-warning}
This guide is for individuals who plan to reuse the existing outlets within the kiosk. If you're not confident in completing this process, consider using an extension cord as an alternative. Make sure the cord supports at least 125V. Keep in mind that, depending on the type of cord used, it may obstruct the removal and reinstallation of the drop bin.
1x 12-AWG/2 or 12AWG/3 Power Cord (25ft)
A thick, durable cable suitable for 20-amp circuits. The 25ft length should give you plenty of wire to work with inside the kiosk. You technically shouldn’t need more than 15 feet, but this allows you to have the proper lengths for daisy chaining from Outlet 1 to Outlet 2
1x GFCI Outlet Tester
Use this to verify that the outlet is properly wired and the GFCI protection works as intended.
1x 3/8" Clamp-on Service Entrance Connector
Prevents stress or accidental tugging from damaging the internal wiring. Required for secure and safe cable entry into the box.
5x 12-10 Yellow Ring Terminals
These will be crimped onto the ground wires to ensure a tight, secure, and corrosion-resistant connection to the outlets and chassis.
1x Wire Stripper/Cutter/Crimper Tool
A basic model will do fine. Used to cut wire to length, strip the outer jacket, and crimp terminals to the exposed copper.
1x GFCI Outlet or 1x 20 Amp Circuit Breaker
Even though you're using 12 AWG wiring rated for 20 amps, GFCI outlets usually max out at 15 amps. Do not exceed the rated amperage.
For permanent or outdoor setups, you may want to install a dedicated 20-amp breaker. If you’re not experienced with electrical panels, hire a licensed electrician to handle this part.
{.is-info}
1x 1/2" Plastic Screw-in Connector Conduit Fitting
Optional, but great for helping keep moisture and rain out of the box, especially if the kiosk is outdoors.
2x 20-Amp 125V Outlets (or better)
Used if you're replacing both receptacles inside the kiosk.
1x 1/2" Plastic Screw-in Connector Conduit Fitting
Great for helping keep moisture and rain out of the box, especially if the kiosk is outdoors. Most of the time, it is ok to re-use the old one, but is a good idea to use a new one to keep water from entering the kiosk.
Ensure all outlet connections are secure and tight before performing any tests. Loose wiring may cause an electrical fire or destroy kiosk equipment.
{.is-warning}
Plug in your GFCI Outlet Tester.
Make sure each outlet shows correct wiring and that GFCI protection functions.
If you get an error, double-check all wire connections, especially Live vs Neutral.
Once everything tests correctly, plug in your kiosk equipment.
